IAI EC ELECYLINDER EC-GD4 Instruction Manual Download

Page: 108 / 208

4-3

perat

ion

ELECYLINDER test operation

Touch [Simple Data Setting].

The screen will switch to the Simple Data Setting window.

  If the position edit password is set to a value other
  than "0000", the password input screen will be
  displayed.

However, if the operating mode is not [Monitor mode],

the Message screen will be displayed.

Switch to Monitor mode by following the displayed instructions.

If the position edit password is set to a value other
than "0000", enter the password and press
the [ENT] key on the touch panel.

The screen will switch to the Simple Data Setting window.

The position edit password is set to "0000" at shipping.
Refer to the teaching pendant manual (ME0355) for information
about changing the password.

Touch the [Homing] button.

The ELECYLINDER returns to the home position.

After home return operation completes,

the [BEnd] and [FEnd] buttons will appear.

Action

4.2 Teaching tool connections and testing operation

Action

Reference

Summary of Contents for EC ELECYLINDER EC-GD4
















































































































































































































Search results

Summary of Contents for EC ELECYLINDER EC-GD4

Reviews:

Related manuals for EC ELECYLINDER EC-GD4

Brands by name

Popular brands

IAI EC ELECYLINDER EC-GD4, Instruction Manual

Search results

Summary of Contents for EC ELECYLINDER EC-GD4

Reviews:

Related manuals for EC ELECYLINDER EC-GD4

Brands by name

Popular brands