IAI EC ELECYLINDER EC-GD4 Instruction Manual Download | Manualshive

Page: 170 / 208

background image

8-3

8. Maintenan

ce and Inspection

8.2 Inspection items and schedule

Follow the maintenance inspection schedule below.
It is assumed that the equipment is operating 8 hours per day.
If the equipment is running continuously night and day or otherwise running at a high operating
rate, inspect more often.

Rod type, table type

Inspection period

External

inspection

Internal

inspection

Greasing

Start of work inspection

○

－

－

1-month inspection

○

－

－

3-month inspection

－

－

○

6-month inspection

○

○

Depends on grease supply

timing (guideline)

Every 6 months thereafter

○

○

Grease supply timing (Guideline)

Maximum operating speed [mm/s]

Grease supply timing (Guideline)

Travel distance

Months

0 to 300 or less

1,250km

12 months

8.2 Inspection items and schedule

«
...
168
169
170
171
172
...
»

Summary of Contents for EC ELECYLINDER EC-GD4

















































































































































































































Reviews:

No comments

Related manuals for EC ELECYLINDER EC-GD4

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: Dahua Pages: 58

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: IAI Pages: 5

ArtNet-DMX Mux16

Brand: DMX4ALL Pages: 21

JetWeb JX2-PRN1

Brand: Jetter Pages: 25

Brand: Nice Pages: 120

Brand: Wilo Pages: 128

Brand: Nautronic Pages: 6

Brand: Redbusbar Pages: 12

Brand: Water Specialist Pages: 36

Smart 4 Universal

Brand: Classic Pages: 12

Brand: Pilz Pages: 9

Explorer Dongle

Brand: Sparkfun Electronics Pages: 16

Brand: Danfoss Pages: 36

Brand: Ascon tecnologic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands