IAI EC ELECYLINDER EC-GD4 Instruction Manual Download

Page: 145 / 208

6-12

aram

Parameter No.5: Smooth accel/decel setting

No. Category

Name

Symbol

Unit

Input range Default setting

at shipping

Smooth

accel/decel setting

MOD0

－

Disabled,

enabled

Disabled

●

The movement waveform for ELECYLINDER operation can be selected.

●

When [Enabled], accel/decel operation becomes smoother (less abrupt).

This softens the shocks of acceleration/deceleration without delaying
the operation time.

●

If [Disabled], the above functionality is not enabled.

Caution

For operation in which the acceleration time or deceleration time exceeds 2 seconds,
do not [Enable] smooth accel/decel settings.
Normal operation will not be possible.

Avoid momentary stops during acceleration or deceleration operation.
Sudden changes (acceleration) will occur, which may be dangerous.

Setting

Acceleration/deceleration

pattern

Operation waveform image

Disabled

Trapezoid

Enabled

S-motion

Time

6.4 Parameter function descriptions

Speed

Time

Summary of Contents for EC ELECYLINDER EC-GD4
















































































































































































































Search results

Summary of Contents for EC ELECYLINDER EC-GD4

Reviews:

Related manuals for EC ELECYLINDER EC-GD4

Brands by name

Popular brands

IAI EC ELECYLINDER EC-GD4, Instruction Manual

Search results

Summary of Contents for EC ELECYLINDER EC-GD4

Reviews:

Related manuals for EC ELECYLINDER EC-GD4

Brands by name

Popular brands