manualshive.com logo in svg

IAI acon, Operation Manual, Page: 192 / 216

Share
Download
IAI acon Operation Manual Download Page 192

4. Appendix

186

OMRON

PLC

IAI RC 

controller 

Switching hub

LAN cable 

LAN cable 

4. Appendix 

 

Examples of connection settings with Omron’s master and Keyence’s master are provided.   

4.1 

Example of Connection Settings with Omron’s Master   

The following devices and software are needed to connect to Omron’s master:   

[1]  PLC CPU unit: 

(Example) CJ2M-CPU31 (with built-in EtherNet/IP) 

[2]  Power unit: 

(Example) PA202 

[3]  Configuration software: 

CX-One V4.0 or later, CX-Programmer V9.12 or later   

[4] Configuration 

software:  CX-One 

V4.0 or later, Network Configurator V3.20 or later 

[5]  Commercially available switching hub (supporting 100BASE-TX) 
[6]  IAI controller of EtherNet/IP specification   
[7]  Straight LAN cable (category 5, 5e or larger) x 2 pcs   

4.1.1 Connection 

Example 

 

A setting example based on the following connection configuration is given.   

(Note)  The power supply, actuator, etc., are not illustrated.   

The connection procedure explained on the following pages is based on the following settings:   

Item

Controller 

PLC

Remarks 

IP address 

192.168.0.1 192.168.0.10 

 

Subnet mask 

255.255.255.0 

255.255.255.0 

 

Default gateway 

0.0.0.0 

0.0.0.0 

Disable the default gateway. 

Baud rate 

Set automatically.  Set automatically.

100 Mbps/full-duplex when link is established 
(The specific settings vary depending on the 
switching hub specification.)

4.1.2 

Setting the Controller   

Actuate an emergency stop on the controller and then start the controller with the MODE switch set to 
MANU. (This is to prevent the motor from starting due to output signals from the PLC.)   
Start the RC PC software and set the user parameters for the controller.   
(Keep all parameters at their factory settings.)   

No.

Name 

Set value 

Remarks 

25 

PIO pattern selection 

0 

Standard mode 

84 

Fieldbus operation mode 

0 

Remote I/O mode 
(I/O sizes: 2 bytes/2 bytes) 

86 

Fieldbus baud rate 

0 

Automatically negotiated. 

87 Network 

type 

7 

EtherNet/IP 

90 

Fieldbus I/O format 

3 

Byte swap/word swap 

140 IP 

address 

192.168.0.1 

 

141 Subnet 

mask 

255.255.255.0   

142 

Default gateway 

0.0.0.0 

Disable the default gateway. 

Summary of Contents for acon

























































































































































































































Reviews:

No comments