manualshive.com logo in svg

IAI acon, Operation Manual, Page: 173 / 216

Share
Download
IAI acon Operation Manual Download Page 173

3. SCON-CA

167

(31) Standstill mode selection (ASC0, ASC1) PLC output signals   

Select the stop mode to be applied while the actuator is standing by to move to the next position after 
completing a positioning.   
If the actuator remains standstill for a long time, the servo is turned off automatically to lower the power 
consumption.  
For details, refer to the operation manual for your controller.   

ASO1 ASO0 

Function 

Remarks 

OFF OFF 

Disabled 

Factory 

setting 

OFF ON 

Automatic servo OFF method 
Parameter No. 36 is enabled for T in the figure below. 

ON OFF 

Automatic servo OFF method 
Parameter No. 37 is enabled for T in the figure below. 

ON ON 

Automatic servo OFF method 
Parameter No. 38 is enabled for T in the figure below. 

Movement command 

Servo ON 

status

Auto servo OFF mode 

(A green LED blinks.) 

Delay time until the servo turns off after 
completion of positioning (sec) 

Target position

Servo status 

Actuator movement 

Summary of Contents for acon

























































































































































































































Reviews:

No comments