manualshive.com logo in svg

IAI acon, Operation Manual, Page: 127 / 216

Share
Download
IAI acon Operation Manual Download Page 127

3. SCON-CA

121

(* In the table, ON indicates that the applicable bit is “1,” while OFF indicates that the applicable bit is “0.”) 

Address Bit 

Symbol 

Function 

Details 

b3 INC 

Incremental specification: 
Absolute position command when the signal is OFF, or 
incremental position command when the signal is ON. 

3.6.11 (24)

b2 DIR 

Pressing direction specification: 
When the signal is OFF, the direction of the position 
obtained by subtracting the positioning band from the 
target position is used. 
When the signal is ON, the direction of the position 
obtained by adding the positioning band to the target 
position is used. 

3.6.11 (22)

b1 PUSH 

Pressing specification: Positioning operation when the 
signal is OFF, or pressing operation when the signal is 
ON.

3.6.11 (21)

Control 

signal 1 

b0 

- 

Cannot be used. 

- 

b15 BKRL 

Forced brake release: The brake is released when the 
signal turns ON. 

3.6.11 (18)

b14 RMOD 

Operation mode: AUTO mode when the signal is OFF, or 
MANU mode when the signal is ON.   

3.6.11 (19)

b13
b12
b11
b10

- 

Cannot be used. 

- 

b9 CLBR 

Load cell calibration command: Calibration is performed 
when this signal turns ON. 

3.6.11 (32)

b8 JOG+ 

+Jog: The actuator moves in the direction opposite home 
when the signal is ON.   

3.6.11 (13)

b7 JOG- 

-Jog: The actuator moves in the direction of home when 
the signal is ON. 

3.6.11 (13)

b6 JVEL 

Jog speed/inching distance switching: Parameter No. 26, 
“Jog speed” and parameter No. 48, “Inching distance” are 
used when the signal is OFF, or parameter No. 47, “Jog 
speed 2” and parameter No. 49, “Inching distance 2” are 
used when the signal is ON. 

3.6.11 (14)

b5 JISL 

Jog/inching switching: Jog operation when the signal is 
OFF, or inching operation when the signal is ON.   

3.6.11 (15)

b4 SON 

Servo ON command: The servo is ON when the signal is 
ON.

3.6.11 (5)

b3 

RES 

Reset: A reset is performed when the signal turns ON. 

3.6.11 (4)

b2 STP 

Pause: A pause command is issued when the signal turns 
ON.

3.6.11 (11)

b1 HOME 

Home return: A home return command is issued when the 
signal turns ON. 

3.6.11 (6)

PLC output 

Control 

signal 2 

b0 DSTR 

Positioning start: A move command is issued when the 
signal turns ON. 

3.6.11 (8)

Summary of Contents for acon

























































































































































































































Reviews:

No comments