manualshive.com logo in svg

IAI acon, Operation Manual, Page: 129 / 216

Share
Download
IAI acon Operation Manual Download Page 129

3. SCON-CA

123

(* In the table, ON indicates that the applicable bit is “1,” while OFF indicates that the applicable bit is “0.”) 

Signal type 

Bit 

Symbol 

Description 

Details 

b15 EMGS 

Emergency stop: An emergency stop is being executed 
when the signal is ON. 

3.6.11 (2)

b14 PWR 

Controller ready: The signal turns ON when the controller 
becomes ready. 

3.6.11 (1)

b13 ZONE2 

Zone 2: The signal is ON when the current position is 
inside the specified zone. 

3.6.11 (12)

b12 ZONE1 

Zone 1: The signal is ON when the current position is 
inside the specified zone. 

3.6.11 (12)

b11 PZONE 

Position zone: The signal is ON when the current position 
is inside the specified position zone. 

3.6.11 (12)

b10 LOAD 

Load output judgment: Reached when the signal is ON, 
or not yet reached when the signal is OFF. (For details, 
refer to the operation manual for the controller.) 

3.6.11 (26)

b9 TRQS 

Torque level: Reached when the signal is ON, or not yet 
reached when the signal is OFF. (For details, refer to the 
operation manual for the controller.) 

3.6.11 (27)

b8 RMDS 

Operation mode: The signal is OFF when the current 
mode AUTO, or ON when the current mode is MANU. 

3.6.11 (19)

b7 GHMS 

Home return in progress: The signal is ON while the 
home return is in progress. 

3.6.11 (6)

b6 PUSHS 

Pressing operation in progress: The signal is ON while 
the pressing operation is in progress. 

3.6.11 (25)

b5 PSFL 

Missed work part during pressing operation: The signal 
turns ON when the actuator missed the work part during 
pressing operation. 

3.6.11 (23)

b4 

SV 

Ready: The signal is ON when the servo is ON. 

3.6.11 (5)

b3 

ALM 

Alarm: The signal turns ON when an alarm occurs. 

3.6.11 (3)

b2 MOVE 

Moving signal: The signal is ON while the actuator is 
moving.

3.6.11 (9)

b1 HEND 

Home return complete: The signal turns ON when the 
home return is completed. 

3.6.11 (6)

PLC input 

Status

signal 2 

b0 PEND 

Positioning complete signal: The signal turns ON when 
the positioning is completed. 

3.6.11 (10)

Summary of Contents for acon

























































































































































































































Reviews:

No comments