manualshive.com logo in svg

IAI acon, Operation Manual, Page: 184 / 216

Share
Download
IAI acon Operation Manual Download Page 184

3. SCON-CA

178

3.9 

EtherNet/IP Related Parameters 

Parameters relating to EtherNet/IP are No. 84 to No. 87 and No. 90. 

Category: C: External interface parameter 

No. Category  Symbol 

Name 

Default value set in the 

factory before delivery 

1

~

83

Refer to operation manual for the 
controller for the parameters No. 1 
through No. 83. 

84 

C 

FMOD 

Field bus operation mode 

0 

86 

C 

FBRS 

Field bus baud rate 

0 

87 C  NTYP 

Network 

type 

7 

90 

C 

FMIO 

Field I/O format 

3 

140 C 

IPAD IP 

address 

192.168.0.1 

141 C 

SNMK 

Subnet 

mask 

255.255.255.0 

142 C 

DFGW 

Default 

gateway 

 

0.0.0.0 

z

  Field bus operation mode (No.84 FMOD) 

Specify the operation mode in parameter No. 84 using a value between 0 and 8. 

Value set in 

parameter No. 84 

Mode

Number of 

occupied bytes

Contents 

0(Factory setting)  Remote I/O mode 

2 

Operation using PIOs   
(24 V I/Os) is performed via   
EtherNet/IP. 

1 Position/simple 

direct mode 

8 

The target position can be set directly using the 
value or the operation can be performed using 
position data value. 
The other values required for the operation are set 
on the position data. 

2 

Half direct value 
mode

16 

In addition to the target position, the speed, 
acceleration/deceleration and pressing current 
value are set directly using the values to perform 
the operation. 

3 

Full direct value 
mode

32

All the values related to the position control are set 
using the values to perform the operation. 

4 

Remote I/O mode 2 

12 

The current position and current speed reading 
functions are added to the functions in the remote 
I/O mode. 

5 Position/simple 

direct mode 2 

8 

Set this value to implement force control in the 
position/simple direct numerical mode. 

6 

Half direct mode 2 

16 

Set this value to implement force control in the half 
direct numerical mode. 

7 

Remote I/O mode 3 

12 

Set this value to implement force control in the 
remote I/O mode. 

8 

Half direct mode 3 

16 

Set this value to switch servo gains or vibration 
damping control parameters in the half direct 
numerical mode. 

Summary of Contents for acon

























































































































































































































Reviews:

No comments