manualshive.com logo in svg

IAI acon, Operation Manual, Page: 175 / 216

Share
Download
IAI acon Operation Manual Download Page 175

3. SCON-CA

169

3.7 I/O 

Signal 

Timings 

When any of the control signal is turned ON to perform the operation of the actuator using the PLC's 
sequence program, the response (status) is returned to the PLC. The maximum response time is expressed 
using the following formula. 

Maximum response time (msec)

䠙

Yt+Xt+3+ command processing time (operation time, etc.) 

Yt: Master Stationslave transmission delay time 
Xt: SlaveMaster Station Transmission Delay Time 

Master Station  For the master station 

 slave transmission delay (Yt) and slave 

 master station 

transmission delay (Xt), refer to the Operation Manuals for the EtherNet/IP master unit and PLC installed in 
the master unit. 

Filed Network Transmission 
Delay Time 

Command

processing time 

PLC sequence program 

Control signal 

Status signal 

SCON

Control signal 

Status signal

Master station 

 slave 

station transmission 
delay time (Yt) 

Slave station 

 master 

station delay time (Xt) 

Summary of Contents for acon

























































































































































































































Reviews:

No comments