Hydrotec HYDROION VAD 125-CS 1 Operating And Maintenance Manual Download Page 45

Page: 45 / 98

45/98

Last change 10/2018 E-P | Subject to technical modifications

The below display is shown when calling the menu point „alarm“ in case of troublefree operation:

record,

warning

and no

alarm

actually evident.

4. Total hardness

The local mains water hardness is programmed in the menu point

total hardness

Setting range 5°dH to 80°dH (89 ppm to 1430 ppm)

5. Operation mode

The main menu item „Operation mode“ is used for release of regeneration. Furthermore
regeneration steps can be skipped under this menu item. It is displayed by a message if a menu
item should not be selectable due to technical reasons.

LED red - OFF

Summary of Contents for HYDROION VAD 125-CS 1



































































































Search results

Summary of Contents for HYDROION VAD 125-CS 1

Reviews:

Related manuals for HYDROION VAD 125-CS 1

Brands by name

Popular brands

Hydrotec HYDROION VAD 125-CS 1, Operating And Maintenance Manual

Search results

Summary of Contents for HYDROION VAD 125-CS 1

Reviews:

Related manuals for HYDROION VAD 125-CS 1

Brands by name

Popular brands