Huawei pRRU3901 Maintenance Manual Download Page 4 | Manualshive

Page: 4 / 52

background image

This chapter describes the RHUB maintenance items, involving the equipment room, equipment,
power system, and grounding system.

3 pRRU Maintenance Items

This chapter describes the pRRU maintenance items, involving equipment and power system.

4 Powering On and Powering Off the RHUB

After the RHUB is powered on, check the indicator status. Power off the RHUB in normal or
emergency mode as required.

5 Powering On and Powering Off the pRRU

After the pRRU is powered on, check the power supply voltage and indicator status. Power off
the pRRU based on the power supply mode.

6 Replacing the RHUB

The RHUB is an indoor convergence unit. It converges multiple pRRUs to the BBU. Replacing
the RHUB interrupts services carried on the serving cell.

7 Replacing an Optical Module

An optical module provides a port for opto-electronic conversion. This enables the transmission
between the RHUB and BBU through the optical fiber. Replacing the optical module requires
removing the optical fibers. This interrupts all the services.

8 Replacing the RF Daughter Board

This section describes the procedures for replacing the RF daughter board of the pRRU. A pRRU
can have two transmission ports or three transmission ports, requiring the same installation
operations. This section uses the pRRU with three transmission ports as an example. Replacing
an RF daughter board interrupts all the services carried on the pRRU.

9 Replacing the Wi-Fi Daughter Board

This section describes the procedures for replacing the Wi-Fi daughter board, which applies only
to a pRRU with three transmission ports.Replacing an Wi-Fi daughter board interrupts all the
services carried on the pRRU.

10 Replacing the pDock Mother Board

This section describes the procedure for replacing the pDock mother board. Replacing the pDock
mother board of a pRRU will interrupt all services carried on the pRRU. A pDock mother board
can have two transmission ports or three transmission ports, requiring the same installation
operations. This section uses the pDock mother board with three transmission ports as an
example.

Conventions

Symbol Conventions

The symbols that may be found in this document are defined as follows.

LampSite
Site Maintenance Guide

About This Document

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

iii

«
...
2
3
4
5
6
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

Brand: Hama Pages: 2

Brand: Bachmann Pages: 2

Brand: Hama Pages: 6

Brand: Hama Pages: 2

Brand: Cequent Pages: 9

FT2A-PWR-IT Series

Brand: Crestron Pages: 2

Brand: Tunturi Pages: 37

Brand: Oben Pages: 8

Brand: Olympus Pages: 14

Brand: Ikan Pages: 6

Brand: ABC Design Pages: 11

Sparq Powerbank 6000

Brand: Zagg Pages: 16

Brand: A-Tach Pages: 2

Brand: GrassFlap Pages: 14

Brand: Impresind Pages: 16

Brand: Fab Fours Pages: 13

juice pack plus

Brand: Mophie Pages: 2

Brand: Landworks Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands