Huawei pRRU3901 Maintenance Manual Download Page 33 | Manualshive

Page: 33 / 52

background image

NOTE

l

The pRRU housing and the RF daughter board can be secured using either Phillips screws or protection
screws, requiring the same installation operations. This section uses Phillips screws as an example to
describe the installation operations.

l

Keep the Phillips screw secure for future use.

Step 5

Remove the RF daughter board installed in slot S1.

NOTICE

Hold the RF daughter board tightly when pulling the handle to prevent the RF daughter board
from falling.

1.

Use the M4 Phillips screwdriver to loosen the Phillips screws on the RF daughter board in
slot S1, as shown in

Figure 8-3

Loosen the Phillips screws

2.

Use the left hand to hold the RF daughter board and the right hand to hold the right handle
of the RF daughter board to remove the RF daughter board and put it into an ESD box or
bag, as shown in

LampSite
Site Maintenance Guide

8 Replacing the RF Daughter Board

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

25

«
...
31
32
33
34
35
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

GFS 10 - Fuel Sensor

Brand: Garmin Pages: 2

Alerts TX60U-IT

Brand: La Crosse Technology Pages: 3

Brand: Warmup Pages: 4

Brand: Yamaha Pages: 33

Brand: Yamaha Pages: 17

Brand: aci Pages: 8

BACnet / Modbus IMMERSION Series

Brand: aci Pages: 8

Brand: aci Pages: 4

GTM 10 - TMC Module

Brand: Garmin Pages: 1

Brand: Neuspeed Pages: 2

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: PRAXIS Pages: 2

Brand: Hama Pages: 75

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: RADARchron Pages: 2

Brand: Ednet Pages: 4

Brand: Spiral Audio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands