Huawei pRRU3901 Maintenance Manual Download Page 34 | Manualshive

Page: 34 / 52

background image

Figure 8-4

Removing the RF daughter board installed in slot S1

Step 6

Install a new RF daughter board in slot S1.

Level the handles of an RF daughter board of the required mode, and insert the handles separately
in the two dowels of slot S1, and use the M4 Phillips screwdriver to tighten the Phillips screws
on the RF daughter board with a torque of 1.4 N•m, as shown in

.

Figure 8-5

Installing the RF daughter board in slot S1

Step 7

Remove the SN label and mode label on the surface of the RF daughter board, as shown in

.

LampSite
Site Maintenance Guide

8 Replacing the RF Daughter Board

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

26

«
...
32
33
34
35
36
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

Brand: Acer Pages: 2

Brand: Acer Pages: 4

Brand: Kargo Master Pages: 5

Brand: Kappa Pages: 4

Brand: Panasonic Pages: 2

Brand: Hagan Pages: 32

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

Brand: Karel Pages: 56

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

Brand: Parrot Pages: 11

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

7400DN - Phaser Color LED Printer

Brand: Xerox Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands