Huawei pRRU3901 Maintenance Manual Download Page 9

Page: 9 / 52

Changes in LampSite Site Maintenance

Guide

This chapter provides information about the changes in different document versions of

LampSite

Site Maintenance Guide

02 (2014-05-27)

This is the second commercial release.

Compared with 01 (2014-04-26), no information is added.

Compared with 01 (2014-04-26), this issue incorporates the following change:

Content

Change Description

Entire document

Added the descriptions about the LTE FDD
+LTE FDD mode.

Compared with 01 (2014-04-26), no information is deleted.

01 (2014-04-26)

This is the first commercial release.

Compared with Draft C (2014-03-26), no information is added.

Compared with Draft C (2014-03-26), this issue incorporates the following change:

Content

Change Description

Entire document

Changed the pRRU name from pRRU with
two Ethernet ports to pRRU with two
transmission ports, and pRRU with three
Ethernet ports to pRRU with three
transmission ports.

LampSite
Site Maintenance Guide

1 Changes in LampSite Site Maintenance Guide

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Summary of Contents for pRRU3901





















































Search results

Summary of Contents for pRRU3901

Reviews:

Related manuals for pRRU3901

Brands by name

Popular brands

Huawei pRRU3901, Maintenance Manual

Search results

Summary of Contents for pRRU3901

Reviews:

Related manuals for pRRU3901

Brands by name

Popular brands