Huawei pRRU3901 Maintenance Manual Download Page 27 | Manualshive

Page: 27 / 52

background image

Follow-up Procedure

l

Place the replaced RHUB into an ESD box or bag. Then, place the ESD box or bag into a
foam-padded carton or the packing box of the new optical module.

l

Record the information about the faulty component in the fault card.

l

Contact the local Huawei office to deal with the faulty component.

LampSite
Site Maintenance Guide

6 Replacing the RHUB

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

19

«
...
25
26
27
28
29
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

I-Class Mark II

Brand: Datamax Pages: 12

Brand: DataSafe Pages: 4

Brand: Cane Creek Pages: 2

Brand: Hard Head Pages: 40

Brand: Harbor Freight Tools Pages: 7

Brand: Racing Pages: 13

EZ Link DAL 150

Brand: Harman Kardon Pages: 16

Brand: ICON Pages: 8

Brand: K&M Pages: 6

Bass Master Rockabilly

Brand: K&K Sound Pages: 2

COMSPHERE 6800 Series

Brand: Paradyne Pages: 155

COMSPHERE 6800 Series

Brand: Paradyne Pages: 44

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

Brand: Parrot Pages: 11

CK 3000 Evolution

Brand: Parrot Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands