Huawei pRRU3901 Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 52

background image

4.1 Powering On the RHUB

The RHUB is powered by AC input.

Prerequisites

The power cable of the RHUB is not connected to power, that is, the power plug is removed.

Context

NOTICE

The RHUB must be powered on within 7 days after it is unpacked, and the period of its power-
off state cannot exceed 7 days during maintenance.

Procedure

Step 1

Insert the power plug to power on the RHUB.

Step 2

Wait 3 to 5 minutes. Then check the status of the RUN indicator.

If the RUN Indicator Is...

It Indicates that...

Then...

Steady on

There is power input, but the
board is faulty.

Disable the power supply,
rectify the board fault, and
then power on the RHUB
again.

Steady off

There is no power input, or an
alarm about the board is
reported.

Disable the power supply and
check the power input again.
If the power input is normal,
rectify the board fault, and
then power on the RHUB
again.

1s on and 1s off

The RHUB is running
properly.

End the power-on check task.

0.125s on and 0.125s off

The board software is being
loaded.

If the loading is not complete
after 5 minutes, disable the
power supply and check
whether the data in the
configuration file is correct.
Rectify the fault and then
power on the RHUB again.

----End

LampSite
Site Maintenance Guide

4 Powering On and Powering Off the RHUB

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

11

«
...
17
18
19
20
21
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

Brand: CAB Pages: 10

Brand: Panasonic Pages: 16

Brand: NEC Pages: 8

Brand: Barco Pages: 2

Brand: A&D Pages: 35

Brand: Hagan Pages: 32

Brand: Kampmann Pages: 32

Brand: madebyzen Pages: 16

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Brand: Omron Pages: 12

Brand: Fantec Pages: 5

Brand: Cequent Pages: 9

Brand: Hama Pages: 138

Brand: CB Sabbiatrici Pages: 43

Jumbo MultiBigShoot

Brand: agno's Pages: 2

Brand: Marantz Pages: 2

Brand: BAFANG Pages: 12

Brand: Trailboss Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands