Huawei pRRU3901 Maintenance Manual Download Page 31 | Manualshive

Page: 31 / 52

background image

8

Replacing the RF Daughter Board

This section describes the procedures for replacing the RF daughter board of the pRRU. A pRRU
can have two transmission ports or three transmission ports, requiring the same installation
operations. This section uses the pRRU with three transmission ports as an example. Replacing
an RF daughter board interrupts all the services carried on the pRRU.

Prerequisites

The replacement takes approximately 5 minutes.

Context

The preferred slot for an RF daughter board depends on the mode of the RF daughter board.

shows the slot for installing the RF daughter boards.

Figure 8-1

Slot for installing the RF daughter boards

NOTE

l

Unless otherwise specified, LTE mode in this document refers to LTE TDD and LTE FDD.

l

The procedures for replacing an RF daughter board in different slots on the pRRU are the same. The
following section uses the procedures for replacing an RF daughter board in slot S1 as an example.

Procedure

Step 1

Instruct the network operator to block the pRRU.

LampSite
Site Maintenance Guide

8 Replacing the RF Daughter Board

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

23

«
...
29
30
31
32
33
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

Brand: Waters Pages: 21

Brand: Kathrein Pages: 7

Brand: Kathrein Pages: 2

Heating Overblanket

Brand: Lanaform Pages: 84

Brand: Lanaform Pages: 84

Brand: Lanaform Pages: 72

Brand: Lanaform Pages: 80

Brand: Navibe Pages: 8

urban iki Junior

Brand: OGK Pages: 62

Brand: CAME Pages: 2

Radfire RAS Series

Brand: Puretec Pages: 8

Brand: Takara Belmont Pages: 24

Brand: E-Bike Pages: 20

AVID DISC BRAKES

Brand: Avid Technology Pages: 2

GemLightbox Aerial

Brand: Picup Media Pages: 13

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: RADARchron Pages: 2

Brand: Ednet Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands