Huawei pRRU3901 Maintenance Manual Download Page 37 | Manualshive

Page: 37 / 52

background image

9

Replacing the Wi-Fi Daughter Board

This section describes the procedures for replacing the Wi-Fi daughter board, which applies only
to a pRRU with three transmission ports.Replacing an Wi-Fi daughter board interrupts all the
services carried on the pRRU.

Prerequisites

The replacement takes approximately 5 minutes.

Context

On a pRRU with three transmission ports, a Wi-Fi daughter board can be installed only in slot
S3, as shown in

Figure 9-1

Slot for installing the Wi-Fi daughter board

Procedure

Step 1

Instruct the network operator to block the pRRU.

l

On the UMTS side, log in to the LMT and run the

BLK BRD

command to block the RF

daughter board.

l

On the LTE side, log in to the LMT and run the

BLK BRD

command to block the RF daughter

board.

Step 2

Ask the AC administrator to change on the AC the MAC address of the corresponding Wi-Fi
daughter board.

LampSite
Site Maintenance Guide

9 Replacing the Wi-Fi Daughter Board

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

29

«
...
35
36
37
38
39
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

Brand: Balboa Pages: 2

Brand: Banner Pages: 12

One Step BRZ0070

Brand: Baby Brezza Pages: 4

Brand: Babboe Pages: 7

Brand: Babboe Pages: 7

MES ACURAS HEAD

Brand: Barco Pages: 131

Brand: DANA Pages: 42

Brand: Yakima Pages: 8

MIW-DUAL-SIGNAL-BAY

Brand: Panamax Pages: 2

Brand: Sanitas Pages: 52

Brand: Obelink Pages: 2

Brand: FujiFilm Pages: 13

Brand: Scame electrical solutions Pages: 8

iBoard IB-ZK406

Brand: APS Auto Parts Specialist Pages: 3

Brand: Cricut Pages: 4

Brute Strength 12057.0271

Brand: Quadratec Pages: 6

Brand: Dufco Pages: 11

Brand: Klarstein Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands