manualshive.com logo in svg

Huawei CX320, User Manual

Share
Download
Huawei CX320 User Manual Download Page 81

Configuration Type

Configuration Item

Network Management and
Monitoring

l

SNMP Configuration

l

RMON Configuration

l

NETCONF Configuration

l

OpenFlow Agent Configuration

l

LLDP Configuration

l

NQA Configuration

l

Mirroring Configuration

l

Packet Capture Configuration

l

NetStream Configuration

l

sFlow Configuration

 

4.9 Backing Up the Configuration File

This topic describes how to back up the configuration file. If configuration errors occur or the
CX320 is faulty, you can use the backup configuration file to restore configuration data.

Back up the configuration file of the CX320 so that the configuration data can be restored if
faults occur.

Prerequisites

Software

WinSCP.exe (third-party free software)

Procedure

Step 1

Log in to the converged switching plane command-line interface (CLI).

Step 2

Log in to the MM910 CLI.

Step 3

Configure the converged switching plane.

Step 4

Save the converged switching plane configuration file.

1.

Run the following command on the CLI of the converged switching plane to view the
configuration file required for the next startup of the converged switching plane:
<HUAWEI> 

display startup

The command output is as follows:

MainBoard: 
  Configured startup system software:        flash:/

xxx

.cc 

  Startup system software:                   flash:/

xxx

.cc 

  Next startup system software:              flash:/

xxx

.cc 

  Startup saved-configuration file:          flash:/vrpcfg.zip 
  

Next startup saved-configuration file:     flash:/vrpcfg.zip 

  Startup paf file:                          default 
  Next startup paf file:                     default 
  Startup patch package:                     NULL 
  Next startup patch package:                NULL

CX320 Switch Module
User Guide

4 Configuring the CX320

Issue 09 (2019-08-02)

Copyright © Huawei Technologies Co., Ltd.

75

Summary of Contents for CX320


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands