manualshive.com logo in svg

Huawei CX320, User Manual

Share
Download
Huawei CX320 User Manual Download Page 73

Step 5

Save the settings.

<HUAWEI> 

save

Warning: The current configuration will be written to the device. Continue? [Y/N]:

Enter Y to save the configuration. The following information is displayed:

Now saving the current configuration to the slot 1 . 
Info: Save the configuration successfully. 
 
begin synchronize configuration to SMM ... 
slot 1: upload configuration to SMM successfully. 
<HUAWEI>

----End

l

Change the initial passwords of BIOS.

l

If the software version of the switching plane is earlier than 6.30, log in to the switching
plane CLI through the serial port and then access the BIOS. There is no other way to
access the BIOS. If the software version of the switching plane is 6.30 or later, log in to
the switching plane CLI over SOL or serial port and then access the BIOS.

l

For the switching plane versions from 6.30 to 6.56 (excluding 6.56), if you access the
switching plane CLI over SOL and then the BIOS, the operations such as changing the
password and system upgrade through disk formatting cannot be performed on the BIOS.
These operations are supported on the BIOS from switching plane version 6.56.

Step 1

Run the following command on the CLI of the converged switching plane to restart the GE
switching plane:

<HUAWEI> 

reboot

The command output is as follows:

Warning: Current configuration will be saved to the next startup saved-
configuration file! Continue? [Y/N]:

Enter Y to save the configuration. The command output is as follows:

Now saving the current configuration.
Save the configuration successfully.

begin synchronize configuration to SMM ...
slot 4: configuration is the same with SMM, needn't sync to SMM.
System will reboot! Continue? [Y/N]: 

Enter Y to restart the converged switching plane.

Step 2

Press 

Ctrl+B

 when the system displays Press CTRL+B to enter BIOS menu.

The command output is as follows:

Password:

Step 3

Enter the BIOS login password.

The BIOS menu screen is displayed:

Enter your choice(1-9):                                                          
                                                                                  

CX320 Switch Module
User Guide

4 Configuring the CX320

Issue 09 (2019-08-02)

Copyright © Huawei Technologies Co., Ltd.

67

Summary of Contents for CX320


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands