Huawei CX320 User Manual Download Page 16

Page: 16 / 113

Function

Description

QoS features

Traffic
classification

Traffic classification based on the combination of
the L2 protocol header, IP quintuple information,
outbound port, and 802.1p priority

Traffic classification based on the C-VID and C-PRI
of QinQ packets

Matching internal packet information encapsulated
in a GRE tunnel

Matching internal packet information encapsulated
in a TRILL tunnel

Matching internal packet information encapsulated
in an MPLS or VXLAN tunnel

Traffic
behavior

Access control after traffic classification

Traffic policing based on traffic classification

Re-marking based on the results of traffic
classification

Class-based packet queuing

Association between traffic classification and traffic
behavior

Priority
mapping

Mapping from 802.1p priorities to PHBs and colors

Mapping from PHBs and colors to 802.1p priorities

Mapping from DSCP to PHBs and colors

Mapping from PHBs and colors to DSCP

Mapping from EXP priorities to PHBs and colors

Queue
scheduling

Priority queuing (PQ) scheduling

Deficit round robin (DRR) scheduling

PQ+DRR scheduling

Weighted round robin (WRR) scheduling

PQ+WRR scheduling

Congestion
avoidance

Tail-drop algorithm

Weighted Random Early Detection (WRED) drop
algorithm

Outbound port
rate limiting

Outbound port rate limiting

ACL-based
simplified
traffic policies

ACL-based packet filtering

ACL-based redirection

ACL-based traffic statistics

CX320 Switch Module
User Guide

2 Product Overview

Issue 09 (2019-08-02)

Summary of Contents for CX320


















































































































Search results

Summary of Contents for CX320

Reviews:

Brands by name

Popular brands

Huawei CX320, User Manual

Search results

Summary of Contents for CX320

Reviews:

Brands by name

Popular brands