manualshive.com logo in svg

Huawei CX320, User Manual

Share
Download
Huawei CX320 User Manual Download Page 109

Warning: Enter diagnose view, return user view by pressing Ctrl+Z. 
Info: The diagnose view is used to debug system hardware and software. Misuse of 
some commands in this view will affect system performance. Therefore, use these 
commands with the guidance of Huawei engineers.     

[~HUAWEI-diagnose]

collect diagnostic information

Info: Succeeded in collecting diagnostic information in slot 3.

[~HUAWEI-diagnose]

display diagnostic-information diag-info.txt

Now saving the diagnostic information to the 
device............................................................................
.............................................................................. 
Info: The diagnostic information was saved to the device successfully.

[~HUAWEI-diagnose]

return

<HUAWEI>

save logfile

Info: Save logfile successfully.

<HUAWEI>

dir

Directory of flash:/ 
 
Idx  Attr     Size(Byte)  Date        Time       FileName                    
 0  drwx              -  Apr 07 2014 22:32:50 $_checkpoint                 
 1  dr-x              -  Feb 21 2014 15:03:54 $_security_info              
 2  -rw-    117,788,305  Jan 01 1970 00:03:53 

xxx.cc

 

 3  -rw-    117,784,209  Feb 21 2014 14:47:03 

xxx.cc

 

 4  -rw-     76,227,537  Feb 21 2014 14:41:45 

xxx.cc

 

 5  drwx              -  Jan 01 1970 00:00:19 POST                         
 6  -rw-         10,568  Feb 21 2014 18:20:01 cfg_from_smm                 
 7  -rw-          6,575  Mar 22 2014 04:14:27 cfg_local                    
 8  -rw-         19,435  Mar 22 2014 04:14:24 device.sys                   
 9  -rw-      1,130,184  Apr 08 2014 16:22:11 diagnostic_information.zip 
10  drwx              -  Apr 08 2014 16:18:55 logfile                      
11  -rw-          1,838  Mar 22 2014 04:14:24 vrpcfg.zip                   
 
1,048,576 KB total (367,972 KB free)

<HUAWEI>

dir logfile/

Directory of flash:/logfile/ 
 
Idx  Attr    Size(Byte)  Date        Time       FileName                     
 0  -rw-     7,971,326  Apr 08 2014 16:35:00 diag.log                      
 1  -rw-       444,920  Feb 21 2014 18:23:11 diaglog_3_20140221182310.log.zip 
 2  -rw-     1,756,870  Apr 08 2014 16:18:55 diagnostic_information.zip    
 3  -rw-     4,269,737  Apr 08 2014 16:45:08 log.log                       
 4  -rw-       354,428  Dec 22 2013 11:32:34 log_3_20131222113233.log.zip  
 5  -rw-       353,715  Jan 16 2014 08:50:19 log_3_20140116085018.log.zip  
 
1,048,576 KB total (367,972 KB free)     

2.

Query stack information.

Record the queried slot numbers and roles of the stacked switch modules.

<HUAWEI>

display stack

-------------------------------------------------------------------------------- 
MemberID Role     MAC              Priority   DeviceType     Bay/Chassis        
                                                                                 
-------------------------------------------------------------------------------- 
2        Standby  dcd2-fcf8-5600    100        CX320           2X/300             
                                                                                 
3        Master dcd2-fcf8-55c0      100        CX320           3X/300             
                                                                                 

CX320 Switch Module
User Guide

6 Common Operations

Issue 09 (2019-08-02)

Copyright © Huawei Technologies Co., Ltd.

103

Summary of Contents for CX320


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands