HP rp7400 Hardware Manual Download Page 137

Page: 137 / 162

137

Service Processor Commands

These are the Service Processor commands effective January 21, 1999.

Table 8

Service Processor (SP) Commands Sorted by Alphabetical Order

Function

Command

Definition

Config

Configure the Automatic System Restart

Config

Configure Asynchronous and Modem parameters

Chassis
Codes

Log a chassis code in the GSP chassis code history buffer

Console

Display the history of the Console

Console

Return to Console Mode

Config

Default configuration

Remote

Disconnect remote or LAN console

Remote

Disable remote or LAN console access

Remote

Enable remote or LAN console access

Help

Display the list of available commands

Admin

Modify GSP inactivity timeouts

Config

Configure LAN connected and PPP console

Paging

Reserve Modem for Paging

Console

Display LAN connected and PPP console status

Remote

Modem Reset

Remote

Display the status of the Modem

Remote

Remote Power Control

Paging

Configure Paging

Status

Display the status of the Power Management Module

Admin

Reset password configuration

Reset

System reset through RST signal

Session

Activate a system session on local or remote port (1 session/remote
and local console)

Status

Display SPU status logs

Admin

Configure security options and access control

Reset

Display the status of the system processors

Session

System reset through INIT signal

Summary of Contents for rp7400



































































































































































Search results

Summary of Contents for rp7400

Reviews:

Related manuals for rp7400

Brands by name

Popular brands

HP rp7400, Hardware Manual

Search results

Summary of Contents for rp7400

Reviews:

Related manuals for rp7400

Brands by name

Popular brands