manualshive.com logo in svg

HP rp7400, Hardware Manual

Share
Download
HP rp7400 Hardware Manual Download Page 5

 

5

System Overview

The following sections provide or point to an overview of the rp7400 server hardware and software.

Hardware overview

For an overview of the Enterprise Server Family hardware go to http://

www.hp.com/go/hp9000_servers-docs

For an overview of the HP-9000 or HP e3000 rp7400 Server hardware go to http://

www.hp.com/go/hp9000_servers-docs

Software Overview

The HP-9000 rp7400 server is designed to operate using HP-UX version 11.0 or newer.

The HP e3000 rp7400 is designed to operate using MPE/iX release 7.0 (uni-processor support) and MPE/iX 
release 7.0 express (multi-processor support).

NOTE

All references to rp7400 are equally applicable to the HP e3000 and n4000.

KEY:

 X - Supported with MPE/iX 7.0

 X* - Supported with MPE/iX 7.0 Express 1 Release

X1 - Supported with MPE/iX 7.5 or later

NOTE

1 and 2 way 550 MHz and 750MHz servers are not supported.

Table 1

Processor 

Speed

Number of Processors Supported

220MHz

1

2

3

4

5

6

7

330MHz

X

380MHz

X

440MHz

X1

X1

500MHz

X*

X*

X*

X*

550MHz

X*

X*

750MHz

X1

X1

Summary of Contents for rp7400



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands