HP ProCurve MSM317 Reference Manual Download Page 92

Page: 92 / 124

CLI commands

Virtual AP context

2-62

authentication server access controller

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

authentication server access controller

Use the access controller to authenticate 802.1X or WPA logins.

authentication server accounting

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

authentication server accounting

Enables RADIUS accounting for this VSC (VAP).

no authentication server accounting

Disables RADIUS accounting for this VSC (VAP).

authentication server accounting radius profile

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

authentication server accounting radius profile

<name>

Sets RADIUS accounting to use the specified RADIUS profile.

no authentication server accounting radius profile

Removes accounting support for 802.1X.

authentication server radius

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

authentication server radius

<name>

Sets the RADIUS profile to use for 802.1X or WPA authentication.

dot1x authentication

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

dot1x authentication (local | radius | active-directory)

Sets the authentication for 802.1X and WPA.

wpa-psk

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

wpa-psk

<key>

Sets the WPA preshared key.

no wpa-psk

Deletes the WPA preshared key.

Parameters

password

Specify a key that is between 8 and 64 ASCII characters in length. It is
recommended that the preshared key be at least 20 characters long, and be
a mix of letters and numbers.

Summary of Contents for ProCurve MSM317





























































































































Search results

Summary of Contents for ProCurve MSM317

Reviews:

Related manuals for ProCurve MSM317

Brands by name

Popular brands

HP ProCurve MSM317, Reference Manual

Search results

Summary of Contents for ProCurve MSM317

Reviews:

Related manuals for ProCurve MSM317

Brands by name

Popular brands