HP ProCurve MSM317 Reference Manual Download Page 76

Page: 76 / 124

CLI commands

Config context

2-46

New

sflow sampling

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

sflow

<receiver>

sampling

<interface>

<rate>

Specifies the number of packets between samples. For example, if set to 5, approximately every
fifth packet will be sampled (There is some jitter introduced purposefully into the sample

collection). A value of 0 disables sampling.

New

sflow polling

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

sflow

<receiver>

polling

<interface>

<interval>

Specifies the maximum interval (seconds) between polling of counters. 0 disables polling.

New

mac lockout entry

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

mac lockout entry

<mac>

Adds a new entry to the MAC lockout list.

no mac lockout entry

<mac>

Removes the entry from the MAC lockout list.

New

show mac lockout

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

show mac lockout

Displays all entries in the MAC lockout list.

New

supplicant 802dot1x

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

supplicant 802dot1x

Enables the 802.1X supplicant.

no supplicant 802dot1x

Disables 802.1X supplicant.

New

supplicant anonymous identity

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

supplicant anonymous identity

<identitiy>

Sets the 802.1X supplicant anonymous identity.

New

supplicant eap

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

supplicant eap (peap0 | peap1 | ttls)

<user>

<password>

Changes the EAP configuration.

Summary of Contents for ProCurve MSM317





























































































































Search results

Summary of Contents for ProCurve MSM317

Reviews:

Related manuals for ProCurve MSM317

Brands by name

Popular brands

HP ProCurve MSM317, Reference Manual

Search results

Summary of Contents for ProCurve MSM317

Reviews:

Related manuals for ProCurve MSM317

Brands by name

Popular brands