HP ProCurve MSM317 Reference Manual Download Page 109

Page: 109 / 124

CLI commands

RADIUS profiles context

2-79

radius-server deadtime

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

radius-server deadtime

<seconds>

Sets the retry interval for access and accounting requests that time-out.

If no reply is received within this interval, the AP switches between the primary and secondary

RADIUS servers (if defined). If a reply is received after the interval expires, it is ignored.

Parameters

<seconds>

Retry interval. Range: 2 - 60 seconds.

radius-server host

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

radius-server host

<primary>

[

<secondary>

]

Sets the addresses of the primary and secondary RADIUS servers.

Parameters

<primary>

IP address of the primary RADIUS server.

<secondary>

IP address of the secondary RADIUS server.

radius-server key 2

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

radius-server key

<primary>

[

<secondary>

]

Sets the primary and secondary secrets used to connect with the RADIUS server.

Parameters

<primary>

Shared secret for the primary RADIUS server.

<secondary>

Shared secret for the secondary RADIUS server.

radius-server message-authenticator

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

radius-server message-authenticator

Include the message authenticator attribute in RADIUS packets.

no radius-server message-authenticator

Do not include the message authenticator attribute in RADIUS packets.

radius-server name

Supported on: MSM422 MSM320 MSM410 MSM310 MSM335

radius-server name

<name>

Changes the name of the RADIUS profile.

Summary of Contents for ProCurve MSM317





























































































































Search results

Summary of Contents for ProCurve MSM317

Reviews:

Related manuals for ProCurve MSM317

Brands by name

Popular brands

HP ProCurve MSM317, Reference Manual

Search results

Summary of Contents for ProCurve MSM317

Reviews:

Related manuals for ProCurve MSM317

Brands by name

Popular brands