manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 75

HP Integrity NonStop NS-Series Operations Guide — 529869-005

4 -1

4

Monitoring EMS Event Messages

When to Use This Section

 on page 4-1

What Is the Event Management Service (EMS)?

 on page 4-1

Tools for Monitoring EMS Event Messages

 on page 4-1

OSM Event Viewer

 on page 4-2

OSM Event Viewer

 on page 4-2

ViewPoint

 on page 4-2

Web ViewPoint

 on page 4-2

Related Reading

 on page 4-2

When to Use This Section

Use this section for a brief description of the Event Management Service (EMS) and 
the tools used to monitor EMS event messages. 

What Is the Event Management Service (EMS)?

The Event Management Service (EMS) is a collection of processes, tools, and 
interfaces that support the reporting and retrieval of event information. Information 
retrieved from EMS can help you to: 

•

Monitor your system or network environment 

•

Analyze circumstances that led up to a problem 

•

Detect failure patterns 

•

Adjust for changes in the run-time environment 

•

Recognize and handle critical problems 

•

Perform many other tasks required to maintain a productive computing operation  

Tools for Monitoring EMS Event Messages

To view EMS event messages for an Integrity NonStop server, use one of these tools:

•

OSM Event Viewer

•

EMSDIST

•

ViewPoint

•

Web ViewPoint

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands