manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 188

Starting and Stopping the System

HP Integrity NonStop NS-Series Operations Guide — 529869-005

15 -12

Reloading Processors

8. Click 

Load

.

9. Check for messages in the System Load dialog box. After the “System Startup 

Complete” message, close the dialog box.  

10. In the Processor Status dialog box, check the status of all processors.  At least one 

processor must be running.  Determine whether you need to reload any remaining 
processors.

11. Dump processor memory, if needed. For more information about dumping 

processor memory, refer to 

Section 9, Processors and Components: Monitoring 

and Recovery

. 

12. If needed, reload any remaining processors.

Reloading Processors

After the system load, use one of these procedures to reload the remaining processors 
in the system:

•

Reloading Processors Using the RELOAD Command

 on page 15-12

•

Reloading Processors Using OSM

 on page 15-12

To reload a halted processor and perform memory dumps, use the reload procedures 
in 

Section 9, Processors and Components: Monitoring and Recovery

. 

Reloading Processors Using the RELOAD Command

1. From a TACL prompt, log on to the system as a super user ID (255,255).

2.  Reload the remaining processors. For example:

> RELOAD (01 - 15), PRIME

3. Check that the reload initiated successfully. This message appears in the TACL 

window: 

PROCESSOR RELOAD: 

nn

For more information about using the RELOAD command, refer to the 

TACL Reference 

Manual

.

Reloading Processors Using OSM

The OSM Service Connection provides a Reload action on the Logical Processor 
object. You can perform the action on a single or multiple processors. The OSM action 
lets you reload an entire processor or omit a Blade Element from the reload action so 
you can dump the PE for that Blade Element before reintegrating it into the running 
processor. To reload a single processor, see 

Section 9, Processors and Components: 

Monitoring and Recovery

.

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands