manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 161

HP Integrity NonStop NS-Series Operations Guide — 529869-005

12- 1

12

Printers and Terminals: Monitoring 
and Recovery

When to Use This Section

 on page 12-1

Overview of Printers and Terminals

 on page 12-1

Monitoring Printer and Collector Process Status

 on page 12-2

Monitoring Printer Status

 on page 12-2

Monitoring Collector Process Status

 on page 12-2

Recovery Operations for Printers and Terminals

 on page 12-3

Recovery Operations for a Full Collector Process

 on page 12-3

Related Reading

 on page 12-3

When to Use This Section

This section provides a brief overview about monitoring and recovery for printers and 
terminals. Monitoring printers and terminals, and using the SPOOLCOM utility is 
discussed more fully in other manuals. Refer to 

Related Reading

 on page 12-3.

Overview of Printers and Terminals 

Printers and terminals are attached to the Integrity NonStop server using one of these 
methods:

•

An asynchronous connection provided by the asynchronous wide area network 
(AWAN) access server for either a terminal or a printer 

•

An asynchronous connection provided by the ServerNet wide area network 
(SWAN) concentrator for either a terminal or a printer

•

A LAN connection provided by an adapter for a printer

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands