manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 206

Creating Startup and Shutdown Files

HP Integrity NonStop NS-Series Operations Guide — 529869-005

16- 6

Establishing a CIIN File

•

The CONFTEXT configuration file located in the $SYSTEM.SYS

nn

 subvolume has 

an INITIAL_COMMAND_FILE entry for the CIIN file.

•

The CIIN file is available in the specified location.

•

The CIIN option is not disabled in the System Load dialog box.

Establishing a CIIN File

The CIIN file is configured at the factory as $DSMSCM.SYS.CIIN. You do not need to 
establish this file. DSM/SCM automatically copies the CIIN file from the initial location 
into each SYS

nn

 you create.

The name of the CIIN file is specified in the INITIAL_COMMAND_FILE entry of the 
CONFTEXT configuration file. 

A system generation program (run from the DSM/SCM application) copies the file 
specified in the CONFTEXT file onto the SYS

nn

 subvolume on the disk and renames 

the file CIIN. If no file is specified in CONFEXT, the operating system does not look for 
the startup file SYS

nn

.CIIN at system startup, even if you enable that file. You cannot 

simply copy a startup file to the SYS

nn

 subvolume and name it CIIN. 

Modifying a CIIN File

After the CIIN file is established on $SYSTEM.SYS

nn

 (as part of running DSM/SCM), 

you can modify the contents of SYS

nn

.CIIN with a text editor such as TEDIT. You 

need not run DSM/SCM again to make these changes effective.

Note.

By default, the CIIN file contains commands needed to start the (permanent) TACL 

process pair and to reload all the processors in the system. Do not place commands to prime 
the processors in the CIIN file.

Note.

The CIIN file must be owned by a member of the super-group (255,

n

). HP recommends 

that you specify “N” for the read access portion of the file security attribute (RWEP) to allow the 
file to be read by any user on the network. For example, you might secure this file “NCCC.”

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands