manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 143

Disk Drives: Monitoring and Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

10- 9

Monitoring the State of Disk Drives

Monitoring the State of Disk Drives

Each disk drive can have two paths, the primary and the backup. (Each M8xxx disk 
drive is forced to have two paths.) The two path states are represented separately. 

Monitoring the Use of Space on a Disk Volume

The Disk Space Analysis Program (DSAP) provides information on disk capacity, free-
space fragments, and page allocation. To check for bad sectors, you can use SCF: 

-> INFO DISK $*, BAD, SEL started, sub magnetic 

You can also use DSAP at a TACL prompt:

> DSAP $* 

Monitoring the Size of Database Files

To check file size:

> FUP INFO 

filename

, DETAIL

A report similar to this one is sent to your home terminal:

Table 10-1. Primary and Backup Path States for Disk Drives

Path State

Description

Degraded

This path of this disk drive has a state other than Up. 

Down

The disk volume or disk path is not logically accessible.

Exclusive

Exclusive ownership has been declared for this disk volume. The 
disk is not accessible to other users.

Executing Diagnostics

The processor is performing diagnostics.

Format in Progress

A disk-format operation is in progress.

Hard Down

The volume or path was put in this state by the SCF ABORT DISK 
command, or cannot be accessed because of a hardware error.

Inaccessible

The disk cannot be accessed.

Not Configured

The component is not configured.

Revive

A mirrored disk is being updated.

Special

Only maintenance-type I/O tasks can be performed on the disk.

Unknown

The path state is unknown. The disk might not be responding.

Up

The disk volume or disk path is logically accessible.

 Bad Sectors Information $DATA14 Primary:
  No bad sectors found.                                         

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands