manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 187

Starting and Stopping the System

HP Integrity NonStop NS-Series Operations Guide — 529869-005

15 -11

Performing a System Load From a Specific

Processor

11. Check for messages in these windows and dialog boxes:

•

System Load dialog box

•

The primary startup event stream window (startup event stream messages) 
and the primary startup TACL window (startup messages)

12. After the System Load dialog box displays the “System Startup Complete” 

message, close the dialog box.  

13. From the Processor Status dialog box, check the status of all processors. At least 

one processor must be running. Determine whether you need to reload any 
remaining processors. If needed, reload any remaining processors. See 

Reloading 

Processors

 on page 15-12.

Performing a System Load From a Specific Processor

Use this method if you need to dump processor memory. See 

Section 9, Processors 

and Components: Monitoring and Recovery

. To perform a system load into a specified 

processor:

1. From the OSM Low-Level Link toolbar, click 

Processor Status

. The Processor 

Status dialog box appears.

2. In the Processor Status dialog box: 

a. Select the processor you want to load.

b. From the Processor Actions drop-down menu, select 

Load

.

c.

Click 

Perform action

.  The System Load dialog box appears.

3. In the System Load dialog box, from the Configuration drop-down menu under 

System Load Configuration, select a system load volume. You can select the 
current $SYSTEM, FCDM-Load, SCSI-Load, or an alternate system volume. 

After you select a system load disk, the Disk Type box indicates whether you’ve 
selected a Fibre Channel (FCDM) or SCSI disk. The Path window is populated with 
information about four load paths. You can double-click a row to make changes for 
this system load.The changes do not persist after the dialog box is closed. 

4. In the SYS

nn

 field, enter the number of the SYS

nn

 subvolume.  The value 

nn

 

must be a two-digit octal number in the range 00 through 77.  

5. In the Configuration File box, select a system configuration file. Normally, you 

choose Current (CONFIG). See 

Configuration File

 on page 15-8.

6. Select or clear the CIIN disabled check box.  If you need to dump processors, you 

must select the CIIN disabled option. 

7. If you need to perform a memory dump of the logical processor you are loading, 

you must omit a Blade Element to prevent the processor element selected from 
being loaded or primed. From the Select Blade Element drop-down menu in the 
Processor Element Dump Settings field, select the Blade Element. 

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands