manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 199

Starting and Stopping the System

HP Integrity NonStop NS-Series Operations Guide — 529869-005

15 -23

Opening Startup Event Stream and Startup TACL

Windows

1. Select 

Start > OutsideView > OutsideView

. The OutsideView dialog box appears.

2. Select 

Session > New

.  The New Session Properties dialog box appears.

3. On the Session tab, in the Session Caption box, type a session caption name such 

as Startup Events or Startup TACL.

4. Click 

IO Properties

. The TCP/IP Properties dialog box appears.

5. Type the DNS name or IP address of the maintenance entity (ME) or integrated 

maintenance entity (IME), followed by a space, and the port number of the window 
type (303 for the startup event stream window, and 301 for the startup TACL 
window).

For example, for the startup event stream window:

me-system1

- 

G100-M02

  

303

me-system1

- 

G100-M03 303

192.231.36.2 303

Then, for the startup TACL window:

me-system1

- 

G100-M02

  

301

me-system1

- 

G100-M03 301

192.231.36.2 301

6. Click 

OK

.  The TCP/IP Properties dialog box closes, and you are returned to the 

New Session Properties dialog box.

7. Click 

OK

.  The startup event stream window or startup TACL window appears.  A 

TACL prompt appears in the startup TACL window.

Consult the OSM Event Viewer for any important system startup messages logged to 
the EMS log that you might have missed while opening the terminal-emulation 
windows.

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands