manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 234

Tools and Utilities for Operations

HP Integrity NonStop NS-Series Operations Guide — 529869-005

B- 4

PATHCOM

PATHCOM

PATHCOM is the interactive interface to the PATHMON process, through which users 
enter commands to configure and manage Pathway applications.

PEEK

Use the PEEK program to gather statistical information about processor activity, 
system storage pools, paging activity, message information, send instructions, and 
interrupt conditions. 

RESTORE

Use the RESTORE utility to copy files from magnetic tape to disk. 

SPOOLCOM

SPOOLCOM allows you to perform these tasks related to printing:

•

Display the status of collectors, devices, print jobs, print processes, routing 
structures, and the spooler itself

•

Change the location, state, or any attribute of your job

•

Delete your print job from the spooler subsystem

•

Restart a device that has gone offline with a device error

Subsystem Control Facility (SCF) 

SCF configures and manages several subsystems that control system processes and 
hardware, including communications paths, disks, tapes, terminals, printers, and 
communications lines. You can run SCF from any workstation or terminal on the 
system after you are logged on. Use SCF to: 

•

Configure and add an object

•

Remove an object

•

Begin or restore access to an object 

•

Stop access to an object 

•

Show static configuration information for an object 

•

Show dynamic information for an object 

•

Automate subsystem startup and shutdown procedures 

•

Power off the system

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands