manualshive.com logo in svg

HP Integrity NonStop NS-series, Operation Manual

Share
Download
HP Integrity NonStop NS-series Operation Manual Download Page 66

Overview of Monitoring and Recovery

HP Integrity NonStop NS-Series Operations Guide — 529869-005

3- 14

Determining Device States

The general format of the STATUS display follows. However, the format varies 
depending on the subsystem.

where:

SCF Object States

Table 3-3

 lists and explains the possible object states that the SCF STATUS command 

can report.

 

subsystem

 STATUS 

object-type object-name

Name          State     PPID    BPID    

attr1

   

attr2

   

attr3

 …

object-name1  state     nn,nnn  nn,nnn  val1    val2    val3  …
object-name2  state     nn,nnn  nn,nnn  val1    val2    val3  …

subsystem

The reporting subsystem name

object-type

The object, or device, type

object-name

The fully qualified name of the object

State

One of the valid object states: ABORTING, DEFINED,            
DIAGNOSING, INITIALIZED, SERVICING, STARTED, START-
ING, STOPPED, STOPPING, SUSPENDED, SUSPENDING, and 
UNKNOWN

PPID

The primary processor number and process identification number 
(PIN) of the object

BPID

The backup processor number and PIN of the object

attrn

The name of an attribute of the object 

valn

The value of that object attribute 

Table 3-3. SCF Object States

(page 1 of 2)

State

Substate

Explanation

ABORTING

The object is being aborted. The object is 
responding to an ABORT command or some type 
of malfunction. In this state, no new links are 
allowed, and drastic measures might be underway 
to reach the STOPPED state. This state is 
irrevocable.

DEFINED

One of the generally defined possible conditions of 
an object with respect to the management of that 
object.

DIAGNOSING

The object is in a subsystem-defined test mode 
entered through the DIAGNOSE command.

INITIALIZED

The system has created the process, but it is not 
yet in one of the operational states.

Summary of Contents for Integrity NonStop NS-series











































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands