HP G2 Series Installation Manual Download Page 31

Page: 31 / 78

Fixed rail kit

Kit overview

This kit contains two - 48.26cm (19 inches) to 78.74cm (31 inches) - depth adjustable rails that mount rack-mountable
products in third-party racks. It also allows for most third-party rack-mountable products to be mounted in racks.

Kit contents (332558-B21)

Item

Quantity

Rail, left

Rail, right

Rail, back

6M nut

M6 screw

Washer, M6 split

Washer, M6 flat

Cage nut

Additional hardware may be supplied for your convenience.

Required tools

The following tools are required for installation:

• Philips No. 1 screwdriver

• 10mm hex nut driver

Installing the fixed rail kit

Warning: To reduce the risk of personal injury or damage to the equipment, be sure that:

Procedure

1. Loosen the hex nuts, and extend the brackets to the desired length.

Fixed rail kit

Summary of Contents for G2 Series















































































Search results

Summary of Contents for G2 Series

Reviews:

Related manuals for G2 Series

Brands by name

Popular brands

HP G2 Series, Installation Manual

Search results

Summary of Contents for G2 Series

Reviews:

Related manuals for G2 Series

Brands by name

Popular brands