HP G2 Series Installation Manual Download Page 33 | Manualshive

Page: 33 / 78

background image

4. Insert screws through the mounting rail into the cage nuts or clip nuts.

5. Tighten the hex nuts.

Warning: To reduce the risk of personal injury or damage to the equipment, be sure that:

WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:

• The rack has anti-tip measures in place. Such measures include floor-bolting, anti-tip feet, ballast, or a combination

as specified by the rack manufacturer and applicable codes.

• The leveling jacks (feet) are extended to the floor.

• The full weight of the rack rests on the leveling jacks (feet).

• The stabilizing feet are attached to the rack if it is a single-rack installation.

• The racks are coupled together in multiple rack installations.

Fixed rail kit

33

«
...
31
32
33
34
35
...
»

Summary of Contents for G2 Series















































































Reviews:

No comments

Related manuals for G2 Series

Workstation Monitor 724

Brand: 3M Pages: 21

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 24

Brand: 3M Pages: 2

SoundPro SE Series

Brand: 3M Pages: 293

Brand: Bamo Pages: 8

Brand: Quantel Pages: 2

Brand: Lumel Pages: 32

YPP-100 Light Piano

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: Flytec Pages: 2

Brand: Omega Pages: 13

Brand: Kane Pages: 35

Brand: Veris Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands