manualshive.com logo in svg

HP G2 Series, Installation Manual

Share
Download
HP G2 Series Installation Manual Download Page 66

Stabilizer kit

Kit overview

The Stabilizer kit provides stability and support and prevents possible tipping when you install, remove, or access equipment
within HPE Advanced G2 Series or HPE Enterprise G2 Series racks.

The stabilizer kit is either required or recommended, depending on your rack configuration. There are four stabilizer kit
options.

• The standard 600-mm (23.6 in) or 800-mm (31.5 in) front foot is required with deployments of stand-alone racks. Rack

rows with four or more bayed racks, without a single rack-mountable component exceeding 99.8 kg (220 lb), do not need a
stabilizer kit installed.

• The heavy duty 600-mm (23.6 in) front foot is required when a single rack-mountable component weighing 99.8 kg (220

lb) or more is installed in a stand-alone rack or in a rack belonging to a rack row of three or fewer bayed racks.

Kit contents (BW932A, BW933A)

Item

Quantity

600-mm (23.62-inch) Front stabilizer mount (BW932A)

1

800-mm (31.5-inch) Front stabilizer mount (BW933A)

1

Stabilizer feet

2

M8 x 30-mm bolt

8

M8 flat washer

8

Required tools

The following tools are required for installation:

• Ratchet with sockets

• Adjustable wrench

Installing the stabilizer

Procedure

1. Raise the rack with leveling feet to align the front foot with the front caster plate.

2. Insert and partially tighten four bolts with washers, securing the front foot to the front caster plate.

Stabilizer kit

66

Summary of Contents for G2 Series















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands