HP G2 Series Installation Manual Download Page 62 | Manualshive

Page: 62 / 78

background image

5. Attach the cable management arm to the sliding shelf with the flat side of the cable management arm mounting bracket

flush with the sliding shelf.

6. Secure the cable management arm to the sliding shelf using two M4 x 12 flat HD screws and M4 external washers with two

M4 nuts on the inside of the shelf.

NOTE: The cable management arm attaches to the rear of the sliding shelf on either the right or left side.

7. Secure the opposite end of the cable management arm to the rack using two M6 x 12 pan HD screws and M6 external

washers.

100 Kilo Sliding Shelf kit

62

«
...
60
61
62
63
64
...
»

Summary of Contents for G2 Series















































































Reviews:

No comments

Related manuals for G2 Series

Brand: Mahr Pages: 384

Brand: Ralston Instruments Pages: 52

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

Brand: horiba Pages: 175

Brand: EPE Conseil Pages: 3

Brand: Primes Pages: 48

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brand: Vanguard Instruments Pages: 85

Prolevel FMC 662

Brand: Endress+Hauser Pages: 52

Brand: Velleman Pages: 18

Brand: MFJ Pages: 5

Xtrinsic MMA8491Q

Brand: Freescale Semiconductor Pages: 4

Brand: Swema Pages: 12

Brand: Vaisala Pages: 2

Brand: SKF Pages: 12

Brand: Hanna Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands