HP G2 Series Installation Manual Download Page 7 | Manualshive

Page: 7 / 78

background image

About this guide

Rack options installation guide

This installation guide includes the instructions for installing rack option kits that are compatible with the HPE Advanced G2
Series and HPE Enterprise G2 Series racks.

For more information, see the HPE Advanced G2 Series Racks User Guide or the HPE Enterprise G2 Series Racks User Guide
on the

Hewlett Packard Enterprise website.

Important safety information

WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:

• The front and rear leveling feet are extended to the floor.

• The full weight of the rack rests on the rear leveling feet and front stabilizer feet.

WARNING: To reduce the risk of personal injury or damage to the rack and equipment, position and secure the racks
according to the instructions in this guide. Failure to do so could result in an unstable installation.

WARNING: Components can be very heavy. To reduce the risk of personal injury or damage to the equipment:

• Remove all pluggable power supplies and modules to reduce the weight of the product before lifting it.

• Observe local occupational health and safety requirements and guidelines for manual material handling.

• Get help to lift and stabilize the product during installation or removal, especially when the product is not fastened

to the rails. When the component weighs more than 22.5 kg (50 lb), at least two people must lift the component into
the rack together. If the component is loaded into the rack above chest level, a third person must assist in aligning
the rails while the other two support the component.

• Use caution when installing the component in or removing the component from the rack; it is unstable when not

fastened to the rails.

About this guide

7

«
...
5
6
7
8
9
...
»

Summary of Contents for G2 Series















































































Reviews:

No comments

Related manuals for G2 Series

Brand: ABB Pages: 8

Brand: E+E Elektronik Pages: 32

Brand: Unipulse Pages: 129

Brand: IDEAL Pages: 11

Brand: IDEAL Pages: 16

Brand: CA.MI Pages: 68

Brand: ISKRAEMECO Pages: 12

RAVTD1760WS Series

Brand: Ravaglioli Pages: 24

Brand: LOVATO ELECTRIC Pages: 10

Brand: e-sylife Pages: 2

Brand: sebaKMT Pages: 131

Brand: Omega Pages: 24

Brand: AccuEnergy Pages: 23

Rainbow RTI-Nano Series

Brand: Laserworld Pages: 25

Optical Power Expert

Brand: EXFO Pages: 93

Brand: KRAL Pages: 48

Brand: B&K Pages: 64

Brand: Omega Engineering Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands