manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 68

 

61 

Parameters 

None 

Description 

Use 

mac-address information enable 

to enable MAC Information globally. 

Use 

undo mac-address information enable 

to restore the default. 

By default, MAC Information is disabled globally. 

Examples 

# Enable MAC Information globally. 

<Sysname> system-view 

[Sysname] mac-address information enable 

mac-address information interval 

Syntax 

mac-address information interval interval-time 

undo mac-address information interval

 

View 

System view 

Default level 

2: System level 

Parameters 

interval-time

: Sets the interval for sending Syslog or trap messages, in the range of 1 to 20,000 

seconds.  

Description 

Use 

mac-address information interval 

to set the interval for sending Syslog or trap messages.  

Use 

undo mac-address information interval 

to restore the default.  

By default, the interval for sending Syslog or trap messages is 1 second. 

Examples 

# Set the interval for sending Syslog or trap messages to 200 seconds. 

<Sysname> system-view 

[Sysname] mac-address information interval 200 

mac-address information mode 

Syntax 

mac-address information mode

 { 

syslog

 | 

trap

 }

 

undo mac-address information mode

 { 

syslog

 | 

trap

 }

 

View 

System view 

Default level 

2: System level 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands