manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 187

 

180 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] port link-type trunk 

[Sysname-Ethernet1/0/1] gvrp registration fixed 

reset garp statistics 

Syntax 

reset garp statistics

 [

 interface interface-list

 ] 

View 

User view 

Default level 

2: System level 

Parameters 

interface interface-list

: Clears the GARP statistics of one or multiple ports.  

You can provide up to 10 port lists, specified in the following ways: 

•

 

As an individual port in the form of 

interface-type interface-number

 

•

 

As a port range in the form of 

interface-type interface-number1

 

to

 

interface-type 

interface-number2

, where the end-port number specified by 

interface-number2

 must be greater 

than the start port number specified by 

interface-number1

.  

Description 

Use 

reset garp statistics

 to clear the GARP statistics on the specified ports. If no ports are specified, 

this command clears the GARP statistics on all ports.  

The cleared statistics include the statistics about GVRP PDUs sent, received, and dropped.  

Related commands: 

display

 

garp statistics

. 

Examples  

# Clear the GARP statistics on all ports.  

<Sysname> reset garp statistics 

 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands