manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 172

 

165 

Set the voice VLAN aging timer only in automatic voice VLAN assignment mode. 

Related commands: 

display voice vlan state

. 

Examples 

# Configure the voice VLAN aging timer as 100 minutes. 

<Sysname> system-view 

[Sysname] voice vlan aging 100 

voice vlan enable 

Syntax 

voice vlan vlan-id enable 

undo voice vlan 

[ 

vlan-id

 ] 

enable

 

View 

Layer 2 Ethernet interface view 

Default level 

2: System level 

Parameters 

vlan-id

: Specifies a VLAN ID, in the range of 2 to 4096.  

Description 

Use 

voice vlan enable 

to enable the voice VLAN feature and configure a VLAN as the voice VLAN 

for a port.  

Use 

undo voice vlan enable 

to disable the voice VLAN feature on a port. 

By default, the voice VLAN feature is disabled on ports. 

Use this command only on a hybrid or trunk port operating in automatic voice VLAN assignment 
mode. 

Examples 

# Enable the voice VLAN feature on Ethernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface ethernet 1/0/1 

[Sysname-Ethernet1/0/1] voice vlan 2 enable 

voice vlan mac-address 

Syntax 

voice vlan mac-address mac-address mask oui-mask 

[

 description text 

] 

undo voice vlan mac

-

address oui

 

View 

System view 

Default level 

2: System level 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands