HP 3100 v2 Series Command Reference Manual Download Page 153

Page: 153 / 239

146

Field Description

Untagged

VLANs for which the port sends packets after removing VLAN tags

port

Syntax

port interface-list

undo port interface-list

View

VLAN view

Default level

2: System level

Parameters

interface-list

: Specifies an interface list, in the format of

interface-list

= {

interface-type

interface-number

[

interface-type interface-number

] }&<1-10>, where

interface-type

interface-number

represents the interface type and interface number and &<1-10> indicates that you

can specify up to 10

interface-type interface-number

[

interface-type interface-number

]

parameters.

Description

Use

port

to assign the specified access ports to the VLAN.

Use

undo port

to remove the specified access ports from the VLAN.

By default, all ports are in VLAN 1.

This command is applicable only on access ports.

By default, all ports are access ports. However, you can manually configure the port type. For more
information, see "

port link-type

You cannot assign Layer 2 aggregate interfaces to a VLAN.

Related commands:

display vlan

Examples

# Assign Ethernet 1/0/1 through Ethernet 1/0/3 to VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] port ethernet 1/0/1 to ethernet 1/0/3

port access vlan

Syntax

port access vlan vlan-id

undo

port

access vlan

View

Layer 2 Ethernet interface view, port group view, Layer 2 aggregate interface view

Default level

2: System level

Summary of Contents for 3100 v2 Series
















































































































































































































































Search results

Summary of Contents for 3100 v2 Series

Reviews:

Brands by name

Popular brands

HP 3100 v2 Series, Command Reference Manual

Search results

Summary of Contents for 3100 v2 Series

Reviews:

Brands by name

Popular brands