manualshive.com logo in svg

HP 3100 v2 Series, Command Reference Manual

Share
Download
HP 3100 v2 Series Command Reference Manual Download Page 113

 

106

 

View 

MST region view 

Default level 

2: System level 

Parameters 

level

: Specifies an MSTP revision level, in the range of 0 to 65535.  

Description 

Use 

revision-level

 to configure the MSTP revision level.  

Use 

undo revision-level

 to restore the default MSTP revision level.  

By default, the MSTP revision level is 0.  

The MSTP revision level, the MST region name, and the VLAN-to-instance mapping table of a 
device determine the device's MST region. When the MST region name and VLAN-to-instance 
mapping table are both the same for two MST regions, they can still be differentiated by their MSTP 
revision levels.  

After configuring this command, run the 

active region-configuration

 command to activate the 

configured MST region level. 

Related commands: 

instance

, 

region-name

, 

vlan-mapping modulo

,

 display stp 

region-configuration

, 

check region-configuration

, and 

active region-configuration

.  

Examples 

# Set the MSTP revision level of the MST region to 5.  

<Sysname> system-view 

[Sysname] stp region-configuration 

[Sysname-mst-region] revision-level 5 

snmp trap enable stp 

Syntax 

snmp-agent trap enable stp

 [

 tc 

]

 

undo snmp-agent trap enable stp

 [

 tc

 ] 

View 

System view 

Default level 

3: Manage level 

Parameters 

tc

: Specifies SNMP notifications for PVST topology changes. 

Description 

 

IMPORTANT: 

This command is available on the HPE 3100 v2 EI switches. 

 

Use 

snmp-agent trap enable stp

 to enable SNMP notifications for PVST topology changes. 

Use 

undo snmp-agent trap enable stp

 to disable SNMP notifications for PVST topology changes. 

By default, SNMP notifications are disabled for PVST topology changes in all VLANs. 

Summary of Contents for 3100 v2 Series
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands