HP 3100 v2 Series Command Reference Manual Download Page 200

Page: 200 / 239

193

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use

display lldp neighbor-information

to display the LLDP information carried in LLDP TLVs sent

from the neighboring devices.

Examples

# Display the LLDP information sent from the neighboring devices received through all ports.

<Sysname> display lldp neighbor-information

LLDP neighbor-information of port 1[Ethernet1/0/1]:

Neighbor index : 1

Update time : 0 days,0 hours,1 minutes,1 seconds

Chassis type : MAC address

Chassis ID : 000f-0055-0002

Port ID type : Interface name

Port ID : Ethernet1/0/1

Port description : Ethernet1/0/1 Interface

System name : HPE

System description : HPE Comware Platform Software

System capabilities supported : Repeater,Bridge,Router

System capabilities enabled : Repeater,Bridge,Router

Management address type : ipv4

Management address : 192.168.1.55

Management address interface type : IfIndex

Management address interface ID : Unknown

Management address OID : 0

Port VLAN ID(PVID): 1

Port and protocol VLAN ID(PPVID) : 1

Port and protocol VLAN supported : Yes

Port and protocol VLAN enabled : No

VLAN name of VLAN 1: VLAN 0001

Auto-negotiation supported : Yes

Auto-negotiation enabled : Yes

OperMau : speed(100)/duplex(Full)

Power port class : PD

PSE power supported : No

PSE power enabled : No

PSE pairs control ability : No

Power pairs : Signal

Port power classification : Class 0

Summary of Contents for 3100 v2 Series
















































































































































































































































Search results

Summary of Contents for 3100 v2 Series

Reviews:

Related manuals for 3100 v2 Series

Brands by name

Popular brands

HP 3100 v2 Series, Command Reference Manual

Search results

Summary of Contents for 3100 v2 Series

Reviews:

Related manuals for 3100 v2 Series

Brands by name

Popular brands