HP 16555A Service Manual Download Page 89

Page: 89 / 141

Verify the test signal

Check the clock pulse width. Using the oscilloscope, verify that the clock pulse
width is 3.480 ns, +20 ps or -80 ps.

Enable the pulse generator channel 1 and channel 2 outputs (LED off).

In the oscilloscope Timebase menu, select Scale: 1.000 ns/div.

In the oscilloscope Timebase menu, select Position. Using the oscilloscope knob,
position the clock waveform so that the waveform is centered on the screen.

On the oscilloscope, select [Shift] + width: channel 2, then select [Enter] to display the
clock signal pulse width (+ width(2)).

If the pulse width is outside the limits, adjust the pulse generator channel 2 width until
the pulse width is within limits.

Testing Performance

To perform the multicard test

3–62

Summary of Contents for 16555A














































































































































Search results

Summary of Contents for 16555A

Reviews:

Related manuals for 16555A

Brands by name

Popular brands

HP 16555A, Service Manual

Search results

Summary of Contents for 16555A

Reviews:

Related manuals for 16555A

Brands by name

Popular brands