Horizon Fitness Super Cub dsm Instruction Manual Download | Manualshive

Page: 27 / 29

background image

27

HobbyZone Super Cub • Instruction Manual

Warranty and Service Contact Information

Parts Contact Information

Country of

Purchase

Horizon Hobby

Address

Phone Number /

Email Address

United States Sales

4105 Fieldstone Rd

Champaign, Illinois, 61822

USA

800-338-4639

[email protected]

United

Kingdom

Horizon Hobby Limited

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS, United Kingdom

+44 (0) 1279 641 097

[email protected]

Germany

Horizon Hobby GmbH

Hamburger Str. 10

25335 Elmshorn, Germany

+49 4121 46199 60

[email protected]

France

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil

Matin

91230 Montgeron

+33 (0) 1 60 47 44 70

infofrance@horizonhobby.

com

Country of

Purchase

Horizon Hobby

Address

Phone Number /

Email Address

United States

of America

Horizon Service Center

(Electronics and engines)

4105 Fieldstone Rd

Champaign, Illinois, 61822

USA

877-504-0233

Online Repair Request:

visit www.horizonhobby.

com/repairs

Horizon Product Support

(All other products)

4105 Fieldstone Rd

Champaign, Illinois, 61822

USA

877-504-0233

productsupport@horizon

-

hobby.com

United

Kingdom

Horizon Hobby Limited

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS, United Kingdom

+44 (0) 1279 641 097

[email protected]

Germany

Horizon Technischer

Service

Hamburger Str. 10

25335 Elmshorn, Germany

+49 4121 46199 66

[email protected]

France

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil

Matin

91230 Montgeron

+33 (0) 1 60 47 44 70

infofrance@horizonhobby.

com

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interfer

-

ence, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

cauTion:

Changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority

to operate the equipment.

This product contains a radio transmitter with wireless technology which

has been tested and found to be compliant with the applicable regulations

governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency

range.

Antenna Separation Distance

When operating your Spektrum transmitter, please be
sure to maintain a separation distance of at least 5 cm
between your body (excluding fingers, hands, wrists,
ankles and feet) and the antenna to meet RF exposure
safety requirements as determined by FCC regulations.
These illustrations show the approximate 5 cm RF
exposure area and typical hand placement when oper

-

ating your Spektrum transmitter.

«
...
25
26
27
28
29
»

Summary of Contents for Super Cub dsm






























Reviews:

No comments

Related manuals for Super Cub dsm

Brand: NOCH Pages: 2

NIEUPORT 28 ARF

Brand: Maxford USA Pages: 16

Brand: Cobra Helicopter Pages: 40

Animated Caboose 73-6729-250

Brand: Lionel Pages: 4

Brand: Mega Construx Pages: 32

Zlin Z-37A Cmelak

Brand: KOR MODEL Pages: 21

Brand: Radica Games Pages: 2

L.O.L. SURPRISE! O.M.G. ROYAL BEE

Brand: MGA Entertainment Pages: 2

Brand: Step2 Pages: 4

Holiday Tradition Express

Brand: Lionel Pages: 16

Brand: A4 Pages: 20

Brand: THE WORLD MODELS Pages: 20

Brand: GRAUPNER Pages: 46

Brand: Jamara Pages: 28

Impulse Laser Gun Rifle Set

Brand: Jamara Pages: 8

E-FLITE UMX ASK-21

Brand: BNF Pages: 21

Let it Roll! Bowling Alley

Brand: Our Generation Pages: 2

ROCKWELL AERO COMMANDER SHRIKE

Brand: Black Horse Model Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands