manualshive.com logo in svg

Horizon Fitness Super Cub dsm, Instruction Manual, Page: 21 / 29

Share
Download
Horizon Fitness Super Cub dsm Instruction Manual Download Page 21

21

HobbyZone Super Cub • Instruction Manual

Disassembly

1. Remove spinner 

A

 from propeller 

B

 and hex nut 

 

(spinner is tight on hex nut). 

2. Remove hex nut, washer and propeller from gear shaft 

F

.

3. Remove 3 screws and cowl 

C

 from fuselage.

4. Remove 4 screws, 4 washers and gearbox 

E

 from firewall 

G

. 

5. In the fuselage, disconnect 2 bullet connectors of motor 

D

 from ESC 

 

connectors (motor wire colors align with ESC wire colors) and remove motor 
wires from fuselage.

6. Disconnect Receiver/ESC unit and remove unit from retainer in fuselage. 
7. Remove hex nut, washer, spacer and front bearing from gear shaft. 
8. Remove gear shaft and rear bearing from gearbox. 
9. Remove 2 screws, 2 rubber washers and motor 

D

 from gearbox. 

Assembly

10. Assemble model by obeying instructions above in reverse. 
11. Make sure propeller size numbers (9 X 6) face forward. The propeller fits on 

hex nut on gear shaft. 

12. Make sure gear on gear shaft and pinion gear on motor correctly align. 
13. Make sure wires are not pinched or damaged when model is assembled. 
14. Use clear tape to hold receiver antennas in fuselage so 2 antennas are kept 

at right angles to each other for correct receiver operation.

Note: 

Threadlock may be required on the 2 screws holding motor in gearbox to 

prevent loosening from vibration.

CAUTION

: DO NOT handle the spinner, propeller, motor or Receiver/ESC 

unit while the battery is connected to the Receiver/ESC. Personal injury 
could result.

Service of Power Components

M1.5X6

M2.5X6

M2X25

G

F

E

D

C

B

A

Summary of Contents for Super Cub dsm






























Reviews:

No comments